Ciena 180-3360-900 Compatible 400G QSFP-DD Transceiver Module

Product Highlights

• Compatible alternative to Ciena 180-3360-900
• 400G connectivity at 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+
• Optical wavelength: 1528.58-1567.54nm
• Specified reach: 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km
• Duplex LC/UPC / SMF interface
• Digital diagnostic monitoring: Support
• Operating temperature: 0℃ to 75°C

Specifications

Applications and Optical Link Design

This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.

Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.

For this coherent interface, document the wavelength plan and modulation or FEC settings before commissioning. Measure span loss and verify adequate OSNR. Interoperability depends on compatible coherent modes as well as form factor, so another coherent part number must not be substituted without engineering review.

Ciena Compatibility and Factory Testing

Factory verification starts with the expected 180-3360-900 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.

Optical Acceptance, Diagnostics and Handling

Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Support. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.

Interoperability and Host Configuration

Check three layers before deployment: host acceptance of the module identity, port support for the stated rate, and a matching optical standard at the remote interface. For breakout operation, confirm lane configuration too. Similar-looking cages can behave differently across speeds and firmware settings. For this model, the principal parameters are data rate 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+, wavelength 1528.58-1567.54nm, rated reach 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km.

Ordering Information

When ordering, specify 180-3360-900, QDD-ZRPH-400GM, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Quality Assurance and Packaging

Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.

Frequently Asked Questions