Dell AOC-Q28DD-8S28-25G Compatible 200G QSFP-DD 8 x 25G NRZ to 8 x 25G SFP28 25G NRZ Active Optical Breakout Cable

Product Highlights

• HT-manufactured compatible alternative for Dell AOC-Q28DD-8S28-25G
• 200G aggregate connectivity at 206.24Gbps (8x 25.78Gbps)
• Interface configuration: QSFP-DD to 8x 25G SFP28
• OM3
• Length configurations covered: 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft) and 70m (230ft)
• Power consumption: QSFP-DD <4W,SFP28 <1W
• Operating temperature: 0 to 70°C (32 to 158°F)

Available Lengths and Corresponding Part Numbers

The documented configurations are 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft) and 70m (230ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.

Compatible OEM Part Numbers

• AOC-Q28DD-8S28-25G-1M
• AOC-Q28DD-8S28-25G-2M
• AOC-Q28DD-8S28-25G-3M
• AOC-Q28DD-8S28-25G-5M
• AOC-Q28DD-8S28-25G-7M
• AOC-Q28DD-8S28-25G-10M
• AOC-Q28DD-8S28-25G-15M
• AOC-Q28DD-8S28-25G-20M
• AOC-Q28DD-8S28-25G-25M
• AOC-Q28DD-8S28-25G-30M
• AOC-Q28DD-8S28-25G-50M
• AOC-Q28DD-8S28-25G-70M

Specifications

Applications and Deployment

Active optical cables integrate optical engines and fiber into a single factory-terminated link. They provide a lighter, longer-reach alternative to copper direct attach without requiring separate transceiver and patch-cord selection. The complete assembly should be routed with bend protection and connected only between compatible optical standards and port modes. For this series, the listed interface is QSFP-DD to 8x 25G SFP28 and the aggregate rate is 200G.

Dell Compatibility and Factory Testing

The verification process combines digital identification with a live link test and diagnostic observation. Host model, hardware revision and software release are useful inputs because qualification behavior can change between platform generations; those details allow platform-specific requirements to be reviewed before the cable is packed. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.

Cable Construction and Routing

For this assembly, the minimum bend radius is 30mm; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is QSFP-DD <4W,SFP28 <1W. These parameters belong in the installation review rather than being treated as catalogue trivia. Route the cable through its intended managers without tension, avoid pressure close to the connector boots and leave enough space to operate the latches. Any service loop must respect the stated bend limit.

Interoperability and Configuration Checks

Check three layers before deployment: the host must accept the cable identification, the port must support the stated aggregate rate, and the lane configuration must match the attached interfaces. On breakout hardware, also confirm channelization and the mapping of every branch. These checks are particularly important when similar-looking ports operate at different speeds or under different firmware settings. For this series, keep the interface rate, AOC construction and length-specific OEM reference together throughout that review.

Ordering Information

Specify the OEM part number and fixed length, then provide the intended host configuration if the link uses channelized or breakout ports. Separate part numbers should be used for separate lengths. This gives the compatibility review enough information to check both the physical assembly and the intended operating mode. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number AOC-Q28DD-8S28-25G identifies the product family; the linked page provides the final length-specific identity.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Quality Assurance and Packaging

Functional inspection covers identification, link establishment and the condition of both connector assemblies. The cable is then protected against dust and connector damage and packed without sharp bends. Labels can include the customer reference and host-platform note when requested for a controlled deployment. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.

Frequently Asked Questions