Customized 4-24 Fibers OM1/OM2 LC/SC/FC/ST/LSH Fiber Optic Pigtail

Projects in the Philippines benefit from keeping the configuration, branch identification and installation requirement consistent across every participating site. This customized pigtail platform is built to the ordered design: OM1/OM2 fiber mode, connector product line, polish, jacket rating and length are all confirmed before release to production. Every leg is factory terminated, polished and optically tested; as a result, the splice point inherits a connector end face that field polishing cannot match.

Product Highlights

• Optical Testing Guarantees Insertion Loss and Returns Loss
• Individually Colored to Easily Match Color-coded Fiber Cable That Will Be Spliced
• Easy-strip Tight-buffered Coating
• Available in PVC (Unrated)/Riser (OFNR)/LSZH Cable Jacket
• Available in LC, SC, FC, ST, LSH Connectors

Specifications

Why pigtails remain the standard termination

A pigtail is half a joint: one end is a terminated under factory control connector, polished and tested under practice control; the other is a bare fiber strand ready for the splice. Fusion-splicing that strand onto the installed cable brings the connector interface quality of the factory to a field channel. The result outperforms field-polished connectors on insertion loss, return loss and long-term stability, and it outperforms pre-terminated trunks when the channel length is uncertain or the pathway is difficult to pre-measure.

Fusion splicing practice that protects the budget

A good splice starts long before the splicer arcs: strip the strand cleanly, cleave square, keep the sleeve staged, and protect the completed splice in the tray with the bend radius respected. The tight-buffered 0.9mm coating on this pigtail strips in one motion and seats cleanly in standard splice sleeves. Done well, a fusion splice adds less attenuation than a connector pair and stays stable for the life of the plant. Project teams in the Philippines can carry this requirement into the site documentation used by each contractor.

Ordering a customized pigtail platform

The customized platform turns a catalog of options into one ordered design: connector product line from LC, SC, FC, ST and LSH; polish as UPC or APC; jacket rating to suit the channel; length to the measured run; and fiber count where the platform offers it. State the combination with the inquiry and the factory confirms the manufacturable specification before release to production. The delivered pigtail then matches the fiber panel hardware, the tray geometry and the channel without field improvisation.

Configuration choices that matter at the tray

Three choices decide how a customized pigtail behaves at the splice point: the connector interface product line must align with the fiber panel adapters, the polish discipline must align with the plant - mixing UPC and APC at one mating point destroys return loss - and the jacket rating must satisfy the pathway code. Getting these right at order time is faster than any field correction, and the factory test report then applies to the particular delivered design.

Choosing the fiber mode for the plant

Single-mode OS2 serves long links, PON access and any plant where distance or wavelength plans matter; the bend-insensitive glass grade keeps attenuation stable in dense trays. OM3 and OM4 multimode serve equipment rooms and data halls where transceiver cost favors short-reach optics. OM1 and OM2 remain in service in legacy plants and should be matched like-for-like. The pigtail mode must equal the fiber cable plant mode - a mismatch splices poorly and performs worse.

Bend-insensitive glass in dense trays

Splice trays and panel rear spaces punish fiber: tight routing, crowded dressing and the occasional hurried re-entry all bend strands beyond what legacy single-mode tolerated. The bend-insensitive grade used in this pigtail holds attenuation stable at bend radii that would fog conventional glass, which keeps the optical path margin intact after the tenth tray opening, not just at commissioning.

A splicing workflow that scales

Productive termination crews work to a fixed routine: mount the tray, dress the fiber cable, splice the pigtails color by color, protect each joint, test each completed port, then close and label. With the routine fixed, a two-person crew terminates a full frame mounting point in a predictable time, and the test record maps cleanly onto the documentation. The consistency additionally makes quality auditable - equivalent materials, equivalent sequence, equivalent pass criteria across every site.

Sparing and kit planning for termination work

Pigtails belong in the termination kit in counted sets with spares: strands break, connectors get contaminated beyond recovery, and a missing spare converts a ten-minute task into a second visit. Plan one spare set per frame mounting point, keep spare strands capped and bagged, and record which set went into which tray so replacement stock may readily be ordered to the identical specification.

Selecting the right pigtail for the job

Five decisions define the order: the connector interface product line must align with the fiber panel, the polish must align with the plant, the fiber mode must align with the fiber cable, the design must align with the channel, and the count must align with the tray capacity. Getting all five right at order time is what turns a box of strands into a dependable termination. Where the need sits outside the standard configurations, the customized platforms cover the remaining combinations.

Production Testing and Quality Assurance

Every pigtail is optically tested before packing: insertion loss and return loss are verified on each terminated leg, and the ferrule end faces are inspected for scratches and contamination. The strands ship coiled, capped and bagged, with the test results provided on order.

Placing an Order and Factory Support

Refer to this pigtail by connector, polish, fiber mode, fiber count and design when submitting a request for a quotation. For configurations outside the listed options - mixed connector families, jacket ratings, lengths or project packaging - send the need with the inquiry and the factory will validate the manufacturable specification. Customers in the Philippines can include multi-site labeling or documentation requirements when requesting a project quotation.