Brocade E1MG-SX-OM Compatible 1G SFP Transceiver Module 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF

Product Highlights

• Compatible alternative to Brocade E1MG-SX-OM
• 1G connectivity at 1.25Gbps
• Optical wavelength: 850nm
• Specified reach: 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF
• Duplex LC / MMF interface
• Digital diagnostic monitoring: Supported
• Operating temperature: 0 to 70°C (23 to 158°F)

Specifications

Applications and Optical Link Design

Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.

Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.

The multimode channel should use the fiber grade associated with the stated 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.

Brocade Compatibility and Factory Testing

Factory verification starts with the expected E1MG-SX-OM identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.

Optical Acceptance, Diagnostics and Handling

For this model, the specified transmit-power range is -9.5~-3dBm; receiver sensitivity is < -17dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.

Interoperability and Host Configuration

Check three layers before deployment: host acceptance of the module identity, port support for the stated rate, and a matching optical standard at the remote interface. For breakout operation, confirm lane configuration too. Similar-looking cages can behave differently across speeds and firmware settings. For this model, the principal parameters are data rate 1.25Gbps, wavelength 850nm, rated reach 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF.

Ordering Information

Use E1MG-SX-OM as the compatibility cross-reference and E1MG-SX-OM as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Quality Assurance and Packaging

Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.

Frequently Asked Questions