LC to LC Simplex FTTA Outdoor Patch Cable, OS2, 7.0mm LSZH

Projects in the Philippines benefit from keeping the configuration, branch identification and installation requirement consistent across every participating site. This simplex FTTA patch cable carries a single OS2 9/125µm single-mode fiber from the baseband equipment to the radio unit, matching the single-fiber optics now common on tower-top radio units. It uses the equivalent 7.0mm LSZH outdoor design as the duplex FTTA product line: Corning G.657.A1 bend-insensitive glass under an UV-stabilized jacket, with a helical steel armored branch protecting the exposed section at each end. The LC UPC interfaces plug directly into BiDi and single-fiber SFP modules used in LTE and 5G radio systems.

Product Highlights

• 7.0mm LSZH UV-stabilized jacket for outdoor exposure
• Helical steel armored branch against rodents and birds
• Stock lengths 3m to 50m; project lengths on request
• LC UPC to LC UPC simplex, OS2 9/125µm single mode
• Matches single-fiber BiDi optics on radio units
• Corning G.657.A1 bend-insensitive fiber, 20/10D bend radius

Specifications

Single-fiber links on modern towers

A growing share of radio units use bidirectional optics that run transmit and receive on one strand. A simplex jumper matches that architecture exactly: one fiber, one connector at each end, no dark strand coiled behind the radio. Using a simplex cord instead of a duplex with one leg parked reduces weight on the tower, simplifies port mapping and removes the risk of a dangling unterminated leg collecting moisture or damage. Project teams in the Philippines can carry this requirement into the site documentation used by each contractor.

Mechanical protection where it counts

The exposed ends of an FTTA run take the real abuse: clamp pressure at the fiber cable entry, vibration from the structure, and wildlife along the channel. The helical steel armored branch on this jumper absorbs that exposure while staying flexible adequate to dress through glands and narrow tray entries. Because the armor is built into the branch rather than added on site, the protection is consistent from the first meter to the connector interface boot.

Bend tolerance for congested enclosures

Junction boxes at the tower base and the fiber cable entry at the RRU shroud leave little room for generous bends. G.657.A1 glass keeps attenuation stable at a 10D static bend radius; as a result, this patch cord may readily be dressed into the provided space without eating into the optical budget. The fiber remains fully compatible with installed G.652.D feeder plant; as a result, the simplex jumper integrates into existing single-mode infrastructure without re-engineering the optical path.

One jacket from shelter to antenna

Because the channel typically begins inside a shelter or cabinet and ends outdoors, the LSZH jacket is specified for both environments: low smoke and halogen-free behavior for indoor sections, UV and chemical resistance for the outdoor climb. A single continuous jacket means no transition hardware and one less potential failure point between the baseband equipment and the radio.

Length selection and customization

Standard size options are stocked for fast delivery: 3m (10ft), 5m (16ft), 10m (33ft), 20m (66ft), 30m (98ft) and 50m (164ft), covering the common shelter-to-tower and frame-to-radio runs this cord is built for. Non-standard lengths beyond this range are manufactured to order. On single-fiber links this patch cord length directly sets the slack stored at the RRU shroud; ordering the measured length keeps the deployment clean and avoids a heavy service loop hanging from the radio unit. Specifying the particular channel length avoids both the slack storage problem of an overlong cord and the strain risk of one that is too short.

Production testing and quality assurance

Each simplex item is terminated with precision zirconia ferrule LC connectors and optically tested before packing. Insertion loss is verified against the 0.3dB ceiling and return loss against the 50dB minimum on every cord, and end-face geometry is inspected so the physical contact stays consistent across repeated mating during commissioning and service work.

Placing an Order and Factory Support

Refer to the LC-LC simplex FTTA product line when submitting a request for a quotation and state the channel length. Where the radio or the baseband side uses SC instead of LC, or where a non-standard breakout is needed at one end, the customized simplex FTTA program covers the equivalent outdoor platform; send the need with the inquiry and the factory confirms the build before release to production. Customers in the Philippines can include multi-site labeling or documentation requirements when requesting a project quotation.