Juniper Networks OSFP-800G-DAC Compatible 800G OSFP 8 x 100G PAM4 IHS/Finned Top Passive Copper Twinax Cable

Product Highlights

• HT-manufactured compatible alternative for Juniper Networks OSFP-800G-DAC
• 800G aggregate connectivity at 800Gbps
• Interface configuration: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)
• Passive DAC / Copper
• Length configurations covered: 0.5m (2ft), 1m (3ft), 1.5m (5ft), 2m (7ft) and 3m (10ft)
• Conductor specification: 30AWG
• Power consumption: 0.1W Per End
• Operating temperature: 0 to 70°C (32 to 158°F)

Available Lengths and Corresponding Part Numbers

The documented configurations are 0.5m (2ft), 1m (3ft), 1.5m (5ft), 2m (7ft) and 3m (10ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.

Compatible OEM Part Numbers

• OSFP-800G-DAC-0.5M
• OSFP-800G-DAC-1M
• OSFP-800G-DAC-1.5M
• OSFP-800G-DAC-2M
• OSFP-800G-DAC-3M

Specifications

Applications and Deployment

Passive twinax cables are commonly selected for short switch-to-switch, switch-to-server and accelerator connections within or between nearby racks. With no separate optical conversion stage, they offer a simple low-power physical link. The assembly must nevertheless remain within the length, signaling rate and qualification limits accepted by both hosts. For this series, the listed interface is OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top) and the aggregate rate is 800G. The stated application is 800G Ethernet.

Juniper Networks Compatibility and Factory Testing

The verification process combines digital identification with a live link test and diagnostic observation. Host model, hardware revision and software release are useful inputs because qualification behavior can change between platform generations; those details allow platform-specific requirements to be reviewed before the cable is packed. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.

Cable Construction and Routing

For this assembly, the conductor specification is 30AWG; the jacket material is PET; the minimum bend radius is 54mm; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 0.1W Per End. These parameters belong in the installation review rather than being treated as catalogue trivia. Route the cable through its intended managers without tension, avoid pressure close to the connector boots and leave enough space to operate the latches. Any service loop must respect the stated bend limit.

Interoperability and Configuration Checks

Check three layers before deployment: the host must accept the cable identification, the port must support the stated aggregate rate, and the lane configuration must match the attached interfaces. On breakout hardware, also confirm channelization and the mapping of every branch. These checks are particularly important when similar-looking ports operate at different speeds or under different firmware settings. For this series, keep the interface rate, DAC construction and length-specific OEM reference together throughout that review.

Ordering Information

Specify the OEM part number and fixed length, then provide the intended host configuration if the link uses channelized or breakout ports. Separate part numbers should be used for separate lengths. This gives the compatibility review enough information to check both the physical assembly and the intended operating mode. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number OSFP-800G-DAC identifies the product family; the linked page provides the final length-specific identity.

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.

Quality Assurance and Packaging

Functional inspection covers identification, link establishment and the condition of both connector assemblies. The cable is then protected against dust and connector damage and packed without sharp bends. Labels can include the customer reference and host-platform note when requested for a controlled deployment. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.

Frequently Asked Questions