QSFP+ to 4 SFP+-40G-AOC-7M23FT 40G QSFP+ to 4 x 10G SFP+ Active Optical Breakout Cable, 7m (23ft)

Product Highlights

• HT-manufactured AOC assembly in 7m (23ft)
• 40G connectivity at 40Gbps
• Interface configuration: QSFP+ to 4 SFP+
• Fixed length and part number: 7m (23ft), QSFP+ to 4 SFP+-40G-AOC-7M23FT
• Minimum bend radius: 30mm

Specifications

Cable Construction and Routing

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Length Selection and Installation Planning

This 7m (23ft) assembly is intended for routes that shorter members of the same family cannot serve comfortably. Before ordering, document the actual pathway and the space available for service access. During installation, secure the integrated optical cable and both optical engines without compressing it into an undersized bundle or leaving its weight suspended from the ports. Within this family, QSFP+ to 4 SFP+-40G-AOC-5M16FT is shorter at 5m (16ft), while QSFP+ to 4 SFP+-40G-AOC-10M33FT is the next longer choice at 10m (33ft); comparing those two boundaries helps avoid both tension and unnecessary slack.

Position Within the Length Range

QSFP+ to 4 SFP+-40G-AOC-7M23FT occupies the middle of this family between QSFP+ to 4 SFP+-40G-AOC-5M16FT at 5m (16ft) and QSFP+ to 4 SFP+-40G-AOC-10M33FT at 10m (33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 3m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Interoperability and Configuration Checks

Check three layers before deployment: the host must accept the cable identification, the port must support the stated aggregate rate, and the lane configuration must match the attached interfaces. On breakout hardware, also confirm channelization and the mapping of every branch. These checks are particularly important when similar-looking ports operate at different speeds or under different firmware settings. For this assembly, the minimum bend radius is 30mm; the jacket material is OFNP.

Network and Protocol Considerations

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include 10G/40Gigabit Ethernet or Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

Breakout Port Mapping

The QSFP+ to 4 SFP+ configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.

Integrated Optical Assembly

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Ordering Information

Specify the OEM part number and fixed length, then provide the intended host configuration if the link uses channelized or breakout ports. Separate part numbers should be used for separate lengths. This gives the compatibility review enough information to check both the physical assembly and the intended operating mode. Keep QSFP+ to 4 SFP+-40G-AOC-7M23FT associated with 7m (23ft) throughout the order and receiving record.

Generic Compatibility and Factory Testing

The verification process combines digital identification with a live link test and diagnostic observation. Host model, hardware revision and software release are useful inputs because qualification behavior can change between platform generations; those details allow platform-specific requirements to be reviewed before the cable is packed. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.

Quality Assurance and Packaging

Functional inspection covers identification, link establishment and the condition of both connector assemblies. The cable is then protected against dust and connector damage and packed without sharp bends. Labels can include the customer reference and host-platform note when requested for a controlled deployment. Volume orders can include customer references on the labels and carton list.

Frequently Asked Questions